Design and Construction of High-Current Line-Commutated Rectifier Based on Parallel Thyristors
Subject Areas : electrical and computer engineeringM. Shahparasti 1 , Mohammad Farzi 2 * , M. Arefian 3 , R. Asad 4 , M. Sharei-pour 5
1 -
2 -
3 -
4 - Iran Univerrsity of Science and Technology
5 -
Keywords: High current thyristor controlled rectifierthyristor valvethyristors in parallel configuration,
Abstract :
This paper presents the process of designing and manufacturing a high-current line-commutated rectifier, which consists of six high current valves. Every valve is constructed through the parallelization of the four thyristors. The design of the physical structure, the placement of busbars, and the arrangement of parallel thyristors are made using an innovative technique so that the current flows equally between them. To ensure equal flow distribution, in addition to the design of hardware structure and the use of suitable methods for simultaneous and accurate triggering of parallel thyristors, a new control technique based on the temperature measurement of each thyristor is proposed. Finally, the experimental results of a 170V, 4000A rectifier are presented to verify the proposed hardware design and control method.
[1] A. B. Plunkett and F. G. Turnbull, "Load-commutated inverter/synchronous motor drive without a shaft position sensor," IEEE Trans. on Industry Applications, vol. 15, no. 1, pp. 63-71, Jan. 1979.
[2] A. K. Chattopadhyay, "High power high performance industrial AC drives-a technology status review," in Proc. IEEE Region 10 and the 3rd Int. Conf. on Industrial and Information Systems, Kharagpur, 2 pp., Kharagpur, India, 8-10 Dec. 2008.
[3] A. Tessarolo, C. Bassi, G. Ferrari, D. Giulivo, R. Macuglia, and R. Menis, "Investigation into the high-frequency limits and performance of load commutated inverters for high-speed synchronous motor drives," IEEE Trans. on Industrial Electronics, vol. 60, no. 6, pp. 2147-2157, Jun. 2013.
[4] E. Espinosa, et al., "Finite control set model predictive control with reduced switching frequency applied to multi-cell rectifiers," in Proc. IEEE Int. Conf. on Industrial Technology, ICIT'15, pp. 2261-2267, Seville, Spain, 17-19 Mar. 2015.
[5] C. Richu Sebastian and P. P. Rajeevan, "A new scheme for SCR based current source inverter fed induction motor drive with open-end stator windings," in Proc. IEEE Int. Conf. on Power Electronics Drives and Energy Systems, PEDES'16, 5 pp., Trivandrum, India, 14-17 Dec. 2016.
[6] E. Fiorucci and G. Bucci, "A low-cost contactless transducer for the measurement of DC currents up to 13 kA for the industry of anodized aluminum," IEEE Trans. on Instrumentation and Measurement, vol. 62, no. 4, pp. 845-852, Apr. 2013.
[7] M. Morati, D. Girod, F. Terrien, V. Peron, P. Poure, and S. Saadate, "Industrial 100-MVA EAF voltage flicker mitigation using VSC-based STATCOM with improved performance," IEEE Trans. on Power Delivery, vol. 31, no. 6, pp. 2494-2501, Dec. 2016.
[8] J. H. Galloway, "Cascading failures in large rectifiers or the myth of N-1," in Record of Conf. Papers Industry Applications Society 52nd Annual Petroleum and Chemical Industry Conf., pp. 129-132, Denver, CO, US, 12-14 Sept. 2005.
[9] H. Behjati and A. Davoudi, "Reliability analysis framework for structural redundancy in power semiconductors," IEEE Trans. on Industrial Electronics, vol. 60, no. 10, pp. 4376-4386, Oct. 2013.
[10] S. Mohamadian, S. Castellan, A. Tessarolo, M. H. Khanzade, and A. Shoulaie, "A novel thyristor-based CSI topology with multilevel current waveform for improved drive performance," IEEE Trans. on Power Electronics, vol. 33, no. 2, pp. 997 - 1006, Feb. 2017.
[11] M. D. Singh and K. B. Khanchandani, Power Electronics, McGraw-Hill, 2006.
[12] W. P. Wilson, "A high-reliability solid-state ignitron replacement," IEEE Trans. on Industry and General Applications, vol. 4, no. 6, pp. 659-664, Nov. 1968.
[13] I. A. Gibbs and D. S. Kimmel, "Active current balance between parallel thyristors in multi-bridge AC-DC rectifiers," IEEE Trans. on Energy Conversion, vol. 16, no. 4, pp. 334-339, Dec. 2001.
[14] A. L. Gattozzi, S. P. Pish, and J. A. Pappas, "Effect of converter packaging techniques on device electrical conduction," IEEE Trans. on Magnetics, vol. 39, no. 1, pp. 418-421, Jan. 2003.
[15] I. A. Gibbs, "Testing of active current balance in parallel thyristor bridges," IEEE Trans. on Energy Conversion, vol. 20, no. 2, pp. 481-484, Jun. 2005.
[16] T. Ding, J. Wang, H. Ding, L. Li, B. Liu, and Y. Pan, "A 35 kA disc-shaped thyristor DC switch for batteries power supply of flat-top pulsed magnetic field," IEEE Trans. on Applied Superconductivity, vol. 22, no. 3, Article No. 5400404, Jun. 2012.
[17] R. Kustom, J. Skiles, S. Akita, and H. Okada, "Experimental studies of current sharing in parallel driven Graetz bridge units for diurnal superconductive magnetic energy storage," IEEE Trans. on Magnetics, vol. 21, no. 2, pp. 1119-1121, Mar. 1985.
[18] R. Fuentes, "Current distribution in paralleled thyristors-a comparative analysis of 5 real cases in high current transformer-rectifiers," in Proc. 39th IAS Annual Meeting Conf. Record of the IEEE Industry Applications Conf., vol.1, pp. 469-476, Seattle, WA, US, 3-7 Oct. 2004.
[19] J. Waldmeyer, Gate-Drive Recommendations for Phase Control Thyristors, ABB, 2002.
[20] SEMIKRON, Application Manual Power Semiconductors, 2011.
[21] ABB Switzerland Ltd, Application Note 5SYA 2034-02: Gate-Drive Recommendations for Phase Control and Bi-Directionally Controlled Thyristors, 2013.
[22] ABB Switzerland Ltd.., Phase Control Thyristor 5STP 21F1400, Doc. No. 5SYA1023, 4 Jan. 2002. https://library.e.abb.com/public/300261548b96749e83257c3100532760/5STP%2021F1400.pdf